Increase your output. . .
A Ream Labeling System from Lowry Computer Products automatically prints and applies
pressure sensitive labels to wrapped reams during the paper converting process. The ream
labeler features a roll-on applicator which ensures positive, accurate placement of labels
in excess of 130 reams per minute. Pressure sensitive labels eliminate the high-maintenance
and safety issues of cold-glue and hot-glue equipment. The adhesive is already applied to
the back of the label and protected by a release liner.
Lowry's Ream Labeling Systems can reduce your downtime by utilizing ream labels which are
printed top to bottom across the web. This provides more than four times the volume of labels
when, decreasing the frequency between media changes. Lowry's Ream Labeling Systems accept
12" OD rolls of label stock-or more than 13,000 6" x 1.25" ream labels.
. . .while decreasing your costs.
A Print and Apply Labeling System can further reduce your costs by reducing your inventory.
Variable information, bar codes and graphics can be printed on-demand from a single stock,
eliminating the cost of product specific label inventory.
Lowry is a solutions oriented integrator of label applicator and data collection systems,
as well as a manufacturer of pressure sensitive labels. With more than twenty years experience
in the pulp & paper industry, we can provide the latest technology that meets your application
needs and exceeds your expectations.
Specifications:
| Ream Labeler |
| Configurations: | | Vertical or Horizontal |
| Applicator Types: | | Brush-on, roll-on or air cylinder assisted roll-on, Tamp, Tamp-Blow |
| Label Width: | | 7" (178mm) maximum; 4" (101mm) minimum |
| Label Length: | | 3" (76mm) maximum; .75" (19mm) minimum |
| Supply Roll: | | 12" (305mm) maximum outside diameter on 3" (76mm) standard core |
| Speed: | | Up to 130 labels per minute, depending on label size |
| Accuracy: | | Up to ± 1/16" with consistent labels and controlled ream handling |
| Electronics: | | Microprocessor |
| Motor: | | Stepper (20" per second dispense) |
| electrical | | 115 VAC, 60 cycles, 5amps |
| Product Sensor: | | Photoelectric |
| Label Sensor: | | Photoelectric, clear label sensor optional |
| Label Verification: | | Bar code scanners and luminescence sensors are available to assure
label placement on each ream |
| Indicator: | | Optional warning light may be configured to indicate low media levels |
| Weight: | | 125 lb. (57 kg) without stand; 300 lb. (136 kg) with stand |
| Space Required: | | Single labeler requires two feet (61cm) of conveyor; dual labelers configured in
zero downtime layout require only four feet (121cm) |
| Air requirements: | | 60-90 PSI, 2cfm, clean, dry, non-oiled |
| Additional Features For Print and Apply Ream Labeler |
| Configuration: | | Zero-que and loop |
| Print Method: | | Direct thermal or thermal transfer |
| Print Speed: | | 2"-12" (51mm-306mm) per second |
| Resolution: | | 300 dpi (11.8 dots/mm) |
| Print Width: | | 6.6" (168mm) maximum |
| Supply Roll: | | 12" (305mm) maximum outside diameter roll |
| Ribbon Dimensions: | | 7.2"W (183mm) x 2956'L (900m) maximum |
| Fonts: | | Bit-mapped and smooth scaleable fonts |
| Bar Codes: | | All popular symbologies included |
| Electronics: | | Dual 32-bit RISC microprocessors; 4MB RAM |
| Communications: | | RS-232, 422, 485 serial interfaces with DB-25;
high-speed parallel
interface |
| Weight: | | 210 lb. (95 kg) without stand; 385 lb. (175 kg) with stand |
| Address: | | Lowry Computer Products, Inc.
1607 - 9th Street
White Bear Lake, MN 55110 |
| Phone/Fax: | | (651) 429-7722 Fax: (651) 429-6006
(800) 429-7722 Fax: (800) 429-6006 |
| Legal: | | Specifications are subject to change without notice.
All trademarks are the property of their respective owners.
©2002 Lowry Computer Products, Inc. All rights reserved |
View Product Information
